They are making several great points related to How to Install a Bathtub as a whole in the content followed below.
Mounting a bath tub isn't specifically brain surgery, but it does require strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably difficult task. If the old bathtub is readily easily accessible, the job can relocate immediately; if you have to open up a wall to remove the old bathtub as well as position the brand-new bathtub, the job is much harder. In either instance, the job is within a house handyman's skills, although you will certainly need an assistant to move out the old tub and also embeded in the new one. See to it you have certified yourself for the work and fit attempting it. As opposed to employing a service provider to take over a halfway-completed task, it is much better to take into consideration utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube connections.
This write-up will aid you set up a brand-new bathtub in your washroom if you have currently bought a new bathtub and do not need to alter the setup of your previous supply of water pipelines.
Your tools as well as product checklist must comprise the following:
Getting ready for the Installment
Firstly, the supporting framework provided with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to ensure that if the faucet features a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps unit to avoid pressure on the bath tub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be rather problematic due to the restricted accessibility that is often the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a towel prepared for the staying water that will originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming during this process. Once the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Before moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Bathtub
Using both wooden boards under its feet, place the bath tub in the needed position. The wood boards are practical in evenly spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four tiny factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the bath tub up until the level checks out level.
To mount taps, fit all-time low of the outermost flexible faucet connector to the ideal supply pipe by making a compression sign up with; then do the same for the various other tap.
Turn on the supply of water as well as examine all joints as well as brand-new pipework for leaks and also tighten them if needed. Fill the tub and likewise check the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the supplier's instruction manual. Tiling and also sealing around the tub should wait up until the bath tub has been made use of at least when as this will certainly settle it right into its final setting.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washers remain in area between the tap and the sink. Protect the faucet in position with the manufacturer offered backnut. When the faucet is securely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet connectors. The former type must be attached to the faucet ends first, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack a rigid seal, triggering the water to penetrate the wall between the bath and the tiling, resulting in issues with moisture as well as feasible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to assimilate your fixtures and installations. They are sold in tubes and cartridges, as well as are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealer can break relatively early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or waterproof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed reading our section about Installing A Bathtub. Thank you for spending some time to browse our blog post. Appreciated our review? Please share it. Let other people check it out. I cherish reading our article about Installing A Bathtub.
This Site